-40%

1450 Watt peak PMA PC MC 24 VOLT AC Wind Turbine Permanent Magnet Generator

$ 100.29

Availability: 93 in stock
  • Refund will be given as: Money Back
  • Item must be returned within: 30 Days
  • Return shipping will be paid by: Seller
  • Restocking Fee: 20%
  • Brand: WINDTURBINEUSA.COM
  • Condition: New
  • All returns accepted: Returns Accepted

    Description

    1450 Watts peak / 2100 RPM at peak load.
    This auction is for a POWER-CORE (PC)
    with MAX-CORE STATOR
    12 VAC 3 phase PMA designed for use.
    with our 28" Hornet or our 34.64" KT propeller (blades)  and with these
    blades can make up to 1000 Watts peak power in high winds (Rated as peak)
    All voltage ranges (VR) are based on use for battery charging with wind power!
    This PMA's is recommended for wind turbines only! Peak at about 2000 RPM.
    1450 Watts peak / 2100 RPM at peak load.
    Designed to operate in an area with low/medium speed averages of 4.4 to 5.6 m/s and greater (Zone 2-5)
    Provides 158 kWh per month (1644.9kWh year)  5.26 kWh per day in a 12.3 mph (5.5 m/s) average wind speed.
    In a zone 7 area this turbine can make up to 200% more power or 10.54 kWh.
    Wind Zones are defined by m/s
    Wind Zone 1      0 – 4.4 m/s
    Wind Zone 2    4.4 – 5.1 m/s
    Wind Zone 3    5.1 – 5.6 m/s
    Wind Zone 4    5.6 – 6.0 m/s
    Wind Zone 5    6.0 – 6.4 m/s
    Wind Zone 6    6.4 – 7.0 m/s
    Wind Zone 7    7.0 – 9.4 m/s  (20-22 mph)
    Make sure your equipment can handle  the peak voltages of each model.
    Batteries are good at absorbing high voltages as long as they do not go over
    their voltage limits and that is why are battery regulators are critical to match
    with our turbines.  We sell many models so make sure the voltages match your battery.
    Thermodyne 1600W Wind Turbine Review
    Video will open in a new window
    Using the iPhone app? Copy this link into Safari:
    TREX blades on SC12 PMA Wind Turbine windgeneering
    Video will open in a new window
    Using the iPhone app? Copy this link into Safari:
    What's better, AC or DC wind turbine PMA's / PMG's
    Video will open in a new window
    Using the iPhone app? Copy this link into Safari:
    Thermodnye Hornet Wind Farm
    Video will open in a new window
    Using the iPhone app? Copy this link into Safari:
    CLICK HERE TO SEE VIDEO #1
    CLICK HERE TO SEE VIDEO #2
    CLICK HERE TO SEE VIDEO #3
    FOR USE ON WIND TURBINES ONLY!!!  NOT FOR USE ON ENGINES OR HYDRO.  PLEASE CONTACT US IF YOU NEED A PMA FOR ENGINE OR HYDRO USE AS THEY ARE VERY DIFFERENT TO WIND PMA TYPES LIKE THIS MODEL.
    CLICK HERE TO SEE VIDEO
    There are plenty of "Look-A-Like" PMA's on the market that cost less.
    The modern type PLATE AND GROOVE rotor that we have developed is the most celebrated and also the most copied type which we pioneered.  The important part is that PLATE AND GROOVE makes power at MUCH LOWER RPM's than the older and traditional Clam type rotor designs that do not provide deep magnetic saturation of the Stator coil offering 600% more power in low RPM scenarios over Clam type designs
    In small wind turbines this is VERY important to make your power in the LOWER RPM ranges.
    Spend a little more and get a LOT more  BANG-FOR-YOUR-BUCK!!!  Money well spent!
    From the beginning GM designed the Delco to run
    WET and even tested them to operate
    Under Water
    !
    Designing an alternator that can survive at 375 degrees F. under the hood of a car operating with rain water coming through the
    radiator and from water puddles is
    No Easy Task!
    Over 100,000,000 10/12si's were produced by Delco and after-market vendors!
    Parts for this legendary 'work-horse' will be available for the next 50+ years.  World's most supported and well recognized alternator model!
    Our Magnets are on an angle
    We make our own brand new
    ROTOR POLE
    SHOES
    AND
    STATOR CORES
    !!!
    Our PMA's are built from the ground up using only 100% ALL new parts!
    (Including the rotor pole shoes and stator coil stacks)
    Our
    NEW
    rotor poles are balanced to within .002 grams for SMOOOOOTH rotation!
    MADE IN THE USA!
    Not a cheap import or copy.